[LTP] [PATCHv2 3/3] network/stress/icmp: use ip xfrm for icmp4-uni-basic01 ipsec testing
Hangbin Liu
haliu@redhat.com
Tue Mar 15 10:50:39 CET 2016
Also check each msg_size in $ICMP_SIZE_ARRAY to make sure the connectvity.
Signed-off-by: Hangbin Liu <haliu@redhat.com>
---
.../stress/icmp/uni-basic/icmp4-uni-basic01 | 96 +++++++---------------
1 file changed, 31 insertions(+), 65 deletions(-)
diff --git a/testcases/network/stress/icmp/uni-basic/icmp4-uni-basic01 b/testcases/network/stress/icmp/uni-basic/icmp4-uni-basic01
index b78ac8f..93ddbbb 100644
--- a/testcases/network/stress/icmp/uni-basic/icmp4-uni-basic01
+++ b/testcases/network/stress/icmp/uni-basic/icmp4-uni-basic01
@@ -50,10 +50,13 @@ $trace_logic
TCID=${TCID:-icmp4-uni-basic01}
TST_TOTAL=1
TST_COUNT=1
+TST_CLEANUP="do_cleanup"
export TCID
export TST_COUNT
export TST_TOTAL
+. ipsec_lib.sh
+
# Test description
tst_resm TINFO "Verify that the kernel is not crashed with receiving and sending various size of ICMP message with the following conditions"
@@ -100,16 +103,12 @@ ICMP_SIZE_ARRAY=${ICMP_SIZE_ARRAY:-"10 100 1000 10000 65507"}
#-----------------------------------------------------------------------
do_cleanup()
{
- # Kill the icmp traffic server
- killall_icmp_traffic
-
# Unset SAD/SPD
- output_ipsec_conf flush | setkey -c >/dev/null 2>&1
- $LTP_RSH $RHOST ${LTPROOT}/'testcases/bin/output_ipsec_conf flush | PATH=/sbin:/usr/sbin:$PATH setkey -c' >/dev/null 2>&1
+ tst_ipsec flush
# Clean up each interface
- initialize_if lhost ${LINK_NUM}
- initialize_if rhost ${LINK_NUM}
+ tst_init_iface lhost ${LINK_NUM}
+ tst_init_iface rhost ${LINK_NUM}
}
@@ -127,10 +126,9 @@ tst_resm TINFO "- Version of IP is IPv${IP_VER}"
tst_resm TINFO "- Size of packets are ( $ICMP_SIZE_ARRAY )"
if $DO_IPSEC ; then
- message=`check_setkey`
+ message=`ip xfrm state`
if [ $? -ne 0 ]; then
- tst_resm TBROK "$message"
- exit 1
+ tst_brkm TBROK "$message"
fi
case $IPSEC_PROTO in
@@ -147,16 +145,14 @@ if $DO_IPSEC ; then
fi
# name of interface of the local/remote host
-lhost_ifname=`get_ifname lhost $LINK_NUM`
+lhost_ifname=`tst_iface lhost $LINK_NUM`
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to get the interface name at the local host"
- exit $TST_TOTAL
+ tst_brkm TBROK "Failed to get the interface name at the local host"
fi
-rhost_ifname=`get_ifname rhost $LINK_NUM`
+rhost_ifname=`tst_iface rhost $LINK_NUM`
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to get the interface name at the remote host"
- exit $TST_TOTAL
+ tst_brkm TBROK "Failed to get the interface name at the remote host"
fi
# Initialize the system configuration
@@ -181,14 +177,12 @@ case $IP_VER in
# Set IPv4 addresses to the interfaces
set_ipv4addr lhost $LINK_NUM $network_part $lhost_host_part
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to add any IP address at the local host"
- exit 1
+ tst_brkm TBROK "Failed to add any IP address at the local host"
fi
set_ipv4addr rhost $LINK_NUM $network_part $rhost_host_part
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to add any IP address at the remote host"
- exit 1
+ tst_brkm TBROK "Failed to add any IP address at the remote host"
fi
# IPv4 address of the local/remote host
@@ -210,14 +204,12 @@ case $IP_VER in
# Set IPv6 addresses to the interfaces
add_ipv6addr lhost $LINK_NUM $network_part $lhost_host_part
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to add any IP address at the local host"
- exit 1
+ tst_brkm TBROK "Failed to add any IP address at the local host"
fi
add_ipv6addr rhost $LINK_NUM $network_part $rhost_host_part
if [ $? -ne 0 ]; then
- tst_resm TBROK "Failed to add any IP address at the remote host"
- exit 1
+ tst_brkm TBROK "Failed to add any IP address at the remote host"
fi
# IPv6 address of the local/remote host
@@ -232,58 +224,32 @@ esac
# Configure SAD/SPD
if $DO_IPSEC ; then
- ipsec_log=`mktemp -p $TMPDIR`
-
- output_ipsec_conf src \
- $IPSEC_PROTO $IPSEC_MODE $SPI $lhost_addr $rhost_addr \
- | setkey -c 2>&1 | tee $ipsec_log
- if [ $? -ne 0 -o -s $ipsec_log ]; then
- tst_resm TBROK "Failed to configure SAD/SPD on the local host."
- rm -f $ipsec_log
- exit 1
+ tst_ipsec src $IPSEC_PROTO $IPSEC_MODE $SPI $lhost_addr $rhost_addr
+ if [ $? -ne 0 ]; then
+ tst_brkm TBROK "Failed to configure SAD/SPD on the local host."
fi
- $LTP_RSH $RHOST ${LTPROOT}/testcases/bin/output_ipsec_conf dst $IPSEC_PROTO $IPSEC_MODE $SPI $lhost_addr $rhost_addr' | PATH=/sbin:/usr/sbin:$PATH setkey -c' 2>&1 | tee $ipsec_log
- if [ $? -ne 0 -o -s $ipsec_log ]; then
- tst_resm TBROK "Failed to configure SAD/SPD on the remote host."
- rm -f $ipsec_log
- exit 1
+ tst_ipsec dst $IPSEC_PROTO $IPSEC_MODE $SPI $lhost_addr $rhost_addr
+ if [ $? -ne 0 ]; then
+ tst_brkm TBROK "Failed to configure SAD/SPD on the remote host."
fi
- rm -f $ipsec_log
fi
-# Make sure the connectvity
-case $IP_VER in
- 4)
- ret=`$LTP_RSH $RHOST ${LTPROOT}/testcases/bin/check_icmpv4_connectivity $rhost_ifname $lhost_addr' ; echo $?'`
- if [ $ret -ne 0 ]; then
- tst_resm TBROK "There is no IPv4 connectivity."
- exit 1
- fi
- ;;
-
- 6)
- ret=`$LTP_RSH $RHOST ${LTPROOT}/testcases/bin/check_icmpv6_connectivity $rhost_ifname $lhost_addr' ; echo $?'`
- if [ $ret -ne 0 ]; then
- tst_resm TBROK "There is no IPv6 connectivity."
- exit 1
- fi
- ;;
-esac
-
-
#-----------------------------------------------------------------------
#
# Main
#
#
-# Run a client
-$LTP_RSH $RHOST "${LTPROOT}/testcases/bin/ns-echoclient -S $lhost_addr -f $IP_VER -s \"$ICMP_SIZE_ARRAY\"" &
-
-sleep $NS_DURATION
-killall_icmp_traffic
-wait
+# Make sure the connectvity
+for msg_size in $ICMP_SIZE_ARRAY; do
+ tst_ping $lhost_ifname $rhost_addr $msg_size
+ if [ $? -ne 0 ]; then
+ tst_brkm TBROK "There is no IPv$IP_VER connectivity with msg_size $msg_size"
+ else
+ tst_resm TPASS "There has IPv$IP_VER connectivity with msg_size $msg_size"
+ fi
+done
#-----------------------------------------------------------------------
#
--
2.5.0
More information about the ltp
mailing list