[LTP] [PATCH v3 05/10] IMA: Read required policy from file

[Mimi Zohar]

On Tue, 2025-01-14 at 12:29 +0100, Petr Vorel wrote:
> Previously snipped of required policy was as a string or regexp.
> Loading required policy from file allows to move code to ima_setup.sh.
> This is a preparation for loading IMA policy from file.
> 
> Check can be done on one or both:
> 1) IMA builtin policy (based on /proc/cmdline)
> 2) IMA policy content (actual content of /sys/kernel/security/ima/policy)
> 
> When missing CONFIG_IMA_READ_POLICY=y on required policy convert: test, but convert
> TFAIL => TCONF.
> 
> Signed-off-by: Petr Vorel <pvorel@suse.cz>

Thanks, Petr.  Really nice patch.  Below is an improvement suggestion.

Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>

> ---
> 
> diff --git a/testcases/kernel/security/integrity/ima/tests/ima_selinux.sh
> b/testcases/kernel/security/integrity/ima/tests/ima_selinux.sh
> index 75f9ba84e4..45fd741b5f 100755
> --- a/testcases/kernel/security/integrity/ima/tests/ima_selinux.sh
> +++ b/testcases/kernel/security/integrity/ima/tests/ima_selinux.sh
> @@ -1,6 +1,7 @@
>  #!/bin/sh
>  # SPDX-License-Identifier: GPL-2.0-or-later
>  # Copyright (c) 2021 Microsoft Corporation
> +# Copyright (c) Linux Test Project, 2021-2025
>  # Author: Lakshmi Ramasubramanian <nramas@linux.microsoft.com>
>  #
>  # Verify measurement of SELinux policy hash and state.
> @@ -14,15 +15,12 @@ TST_CNT=2
>  TST_SETUP="setup"
>  TST_MIN_KVER="5.12"
>  
> -FUNC_CRITICAL_DATA='func=CRITICAL_DATA'
> -REQUIRED_POLICY="^measure.*$FUNC_CRITICAL_DATA"
> +REQUIRED_POLICY_CONTENT='selinux.policy'

The selinux.policy contains a specific critical data measurement rule:
measure func=CRITICAL_DATA label=selinux.  However the test would work with the
generic policy rule "measure func=CRITICAL_DATA", which can be specified on the . 
boot command line via "ima_policy=critical_data".

As long as being able to read the IMA policy is required, in addition to checking
whether the specific critical data rule exists, check whether the generic rule exists
before loading the specific one.

Perhaps all that is needed is defining REQUIRED_BUILTIN_POLICY like:
REQUIRED_BUILTIN_POLICY="critical_data"

>  
>  setup()
>  {
>  	SELINUX_DIR=$(tst_get_selinux_dir)
>  	[ "$SELINUX_DIR" ] || tst_brk TCONF "SELinux is not enabled"
> -
> -	require_ima_policy_content "$REQUIRED_POLICY" '-E' >
> $TST_TMPDIR/policy.txt
>  }
>  
>  # Format of the measured SELinux state data.
> @@ -45,7 +43,7 @@ validate_policy_capabilities()
>  		measured_value=$(echo $1 | awk -F'[=;]' -v inx="$inx" '{print
> $inx}')
>  		expected_value=$(cat
> "$SELINUX_DIR/policy_capabilities/$measured_cap")
>  		if [ "$measured_value" != "$expected_value" ]; then
> -			tst_res TFAIL "$measured_cap: expected: $expected_value,
> got: $digest"
> +			tst_res $IMA_FAIL "$measured_cap: expected:
> $expected_value, got: $digest"
>  			return
>  		fi
>  
> @@ -75,7 +73,7 @@ test1()
>  	# in kernel memory for SELinux
>  	line=$(grep -E "selinux-policy-hash" $ASCII_MEASUREMENTS | tail -1)
>  	if [ -z "$line" ]; then
> -		tst_res TFAIL "SELinux policy hash not measured"
> +		tst_res $IMA_FAIL "SELinux policy hash not measured"
>  		return
>  	fi
>  
> @@ -86,7 +84,7 @@ test1()
>  		tst_brk TCONF "cannot compute digest for $algorithm"
>  
>  	if [ "$policy_digest" != "$expected_policy_digest" ]; then
> -		tst_res TFAIL "Digest mismatch: expected: $expected_policy_digest,
> got: $policy_digest"
> +		tst_res $IMA_FAIL "Digest mismatch: expected:
> $expected_policy_digest, got: $policy_digest"
>  		return
>  	fi
>  
> @@ -116,7 +114,7 @@ test2()
>  	# state matches that currently set for SELinux
>  	line=$(grep -E "selinux-state" $ASCII_MEASUREMENTS | tail -1)
>  	if [ -z "$line" ]; then
> -		tst_res TFAIL "SELinux state not measured"
> +		tst_res $IMA_FAIL "SELinux state not measured"
>  		return
>  	fi
>  
> @@ -129,7 +127,7 @@ test2()
>  	tst_brk TCONF "cannot compute digest for $algorithm"
>  
>  	if [ "$digest" != "$expected_digest" ]; then
> -		tst_res TFAIL "digest mismatch: expected: $expected_digest, got:
> $digest"
> +		tst_res $IMA_FAIL "digest mismatch: expected: $expected_digest,
> got: $digest"
>  		return
>  	fi
>  
> @@ -146,20 +144,20 @@ test2()
>  	enforced_value=$(echo $measured_data | awk -F'[=;]' '{print $4}')
>  	expected_enforced_value=$(cat $SELINUX_DIR/enforce)
>  	if [ "$expected_enforced_value" != "$enforced_value" ]; then
> -		tst_res TFAIL "enforce: expected: $expected_enforced_value, got:
> $enforced_value"
> +		tst_res $IMA_FAIL "enforce: expected: $expected_enforced_value,
> got: $enforced_value"
>  		return
>  	fi
>  
>  	checkreqprot_value=$(echo $measured_data | awk -F'[=;]' '{print $6}')
>  	expected_checkreqprot_value=$(cat $SELINUX_DIR/checkreqprot)
>  	if [ "$expected_checkreqprot_value" != "$checkreqprot_value" ]; then
> -		tst_res TFAIL "checkreqprot: expected:
> $expected_checkreqprot_value, got: $checkreqprot_value"
> +		tst_res $IMA_FAIL "checkreqprot: expected:
> $expected_checkreqprot_value, got: $checkreqprot_value"
>  		return
>  	fi
>  
>  	initialized_value=$(echo $measured_data | awk -F'[=;]' '{print $2}')
>  	if [ "$initialized_value" != "1" ]; then
> -		tst_res TFAIL "initialized: expected 1, got: $initialized_value"
> +		tst_res $IMA_FAIL "initialized: expected 1, got:
> $initialized_value"
>  		return
>  	fi