[Gulli] LMSensors

[Hornet2e]

Salve a tutti vorrei cheidere auito riguardo la configurazione di Lm-sensors 
per la mia scheda madre, una "Abit AI-7 uGuru" per P4.
Ho installato il pacchetto ed eseguito le operazioni che ho trovato sul wiki 
di ubuntu ma fino ad ora non sono riuscito a vedere nemmeno un valore.
Sospetto che c'entri qualcosa la presenza dell'uGuru tuttavia posto il 
resoconto di sensors-detect così che possiate farvi un opinione:

Driver `eeprom' (should be inserted):
  Detects correctly:
  * Bus `SMBus I801 adapter at 0500'
    Busdriver `i2c-i801', I2C address 0x50
    Chip `SPD EEPROM' (confidence: 8)
  * Bus `SMBus I801 adapter at 0500'
    Busdriver `i2c-i801', I2C address 0x52
    Chip `SPD EEPROM' (confidence: 8)

Driver `w83627hf' (should be inserted):
  Detects correctly:
  * ISA bus address 0x0290 (Busdriver `i2c-isa')
    Chip `Winbond W83627HF Super IO Sensors' (confidence: 9)

questo invece è il file che ho estrapolato dai dati che ho ricavato:

bus "i2c-0" "SMBus I801 adapter at 0500" "Non-I2C SMBus adapter"
bus "i2c-1" "SMBus I801 adapter at 0500" "Non-I2C SMBus adapter"

chip "w83627hf-isa-0290"

# Same as above for w83781d except that in5 and in6 are computed differently.
# Rather than an internal inverting op amp, the 82d/83s use standard positive
# inputs and the negative voltages are level shifted by a 3.6V reference.
# The math is convoluted, so we hope that your motherboard
# uses the recommended resistor values.

    label in0 "VCore 1"
    label in1 "VCore 2"
    label in2 "+3.3V"
    label in3 "+5V"
    label in4 "+12V"
    label in5 "-12V"
    label in6 "-5V"
    label in7 "V5SB"
    label in8 "VBat"

# Abit BP6 motherboard has a few differences. VCore1 and VCore2 are the core
# voltages of the two processors. Vtt is memory bus termination resistors
# voltage.
#    label in1 "Vtt"
#    label in8 "VCore2"

    compute in3 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)
    compute in4 ((28/10)+1)*@  ,  @/((28/10)+1)
    compute in5 (5.14 * @) - 14.91  ,  (@ + 14.91) / 5.14
    compute in6 (3.14 * @) -  7.71  ,  (@ +  7.71) / 3.14
    compute in7 ((6.8/10)+1)*@ ,  @/((6.8/10)+1)

# adjust this if your vid is wrong; see doc/vid
#   set vrm 9.0

# set limits to  5% for the critical voltages
# set limits to 10% for the non-critical voltages
# set limits to 20% for the battery voltage

    set in0_min vid*0.95
    set in0_max vid*1.05
    set in1_min vid*0.95
    set in1_max vid*1.05
    set in2_min 3.3 * 0.95
    set in2_max 3.3 * 1.05
    set in3_min 5.0 * 0.95
    set in3_max 5.0 * 1.05
    set in4_min 12 * 0.90
    set in4_max 12 * 1.10
    set in5_max -12 * 0.90
    set in5_min -12 * 1.10
    set in6_max -5 * 0.95
    set in6_min -5 * 1.05
    set in7_min 5 * 0.95
    set in7_max 5 * 1.05
    set in8_min 3.0 * 0.80
    set in8_max 3.0 * 1.20

# set up sensor types (thermistor is default)
# 1 = PII/Celeron Diode; 2 = 3904 transistor;
# 3435 = thermistor with Beta = 3435
# If temperature changes very little, try 1 or 2.
#   set sensor1 1
#   set sensor2 2
#   set sensor3 3435

# examples for temperature limits
#    set temp1_over 40
#    set temp1_hyst 37
#    set temp2_over 52
#    set temp2_hyst 47
#    set temp3_over 52
#    set temp3_hyst 47

se potete mandatemi anche delle configurazioni funzionanti di sensors.conf 
tramite e-mail così che possa capire ancora meglio.
Ciao!

P.S.
Ho già caricato i moduli necessari!